Edelbrock E-Series Cylinder Head Bolt Kit #85332 is designed for use on Jeep 4.0L inline six-cylinder engines using ┬╜-inch head bolts. This high-quality E-Series bolt kit will pair perfectly with Edelbrock's Jeep Cylinder Head #50159 and #50169 and will also fit the 4.2L inline six-cylinder engine if using Edelbrock heads. E-Series bolts have a yield tensile strength of 190,000 PSI for strong and reliable loading with generous filleting throughout to eliminate stress risers. Bolt threads are rolled after heat-treating for superior form and strength, while a small hex head provides extra space for socket clearance in tight situations. E-Series Cylinder Head Bolts have a durable black oxide finish with sealer and come with the distinctive Edelbrock ΓÇ£E" stamped into the head.
Specifications:
| Description_ABR |
HeadBoltKit |
| Description_ASM |
Jeep:Inline-Six:242 (4.0L) |
| Description_DEF |
Engine Cylinder Head Bolt Set |
| Description_DES |
Edelbrock E-Series Cylinder Head Bolt Kit #85332 for Jeep 4.0L Inline Six Engine |
| Description_INV |
Edelbrock Cylinder Head Bolt Kit #85332 |
| Description_FAB |
For Jeep 4.0L inline six with ┬╜-inch bolt diameter |
| Description_FAB |
Yield tensile strength of 190,000 PSI for strength |
| Description_FAB |
Heat treating with rolled threads for superior form & strength |
| Description_FAB |
Black-oxide finish with sealer |
| Description_FAB |
Edelbrock ΓÇ£E" logo stamped on bolt head. |
| Description_EXT |
Edelbrock #85332 Head Bolt Kit is for Jeep 4.0L inline six engines using 1/2" head bolts with Edelbrock #50159 and #50169 Cylinder Heads. This Head Bolt Kit will also fit AMC/Jeep 4.2L Inline Six if using our cylinder heads. |
| Description_MKT |
Edelbrock E-Series Cylinder Head Bolt Kit #85332 is designed for use on Jeep 4.0L inline six-cylinder engines using ┬╜-inch head bolts. This high-quality E-Series bolt kit will pair perfectly with Edelbrock's Jeep Cylinder Head #50159 and #50169 and will also fit the 4.2L inline six-cylinder engine if using Edelbrock heads. E-Series bolts have a yield tensile strength of 190,000 PSI for strong and reliable loading with generous filleting throughout to eliminate stress risers. Bolt threads are rolled after heat-treating for superior form and strength, while a small hex head provides extra space for socket clearance in tight situations. E-Series Cylinder Head Bolts have a durable black oxide finish with sealer and come with the distinctive Edelbrock ΓÇ£E" stamped into the head. |
| Description_LAB |
Edelbrock E-Series Cylinder Head Bolt Kit #85332 for Jeep 4.0L Inline Six Engine |
| Description_SHP |
None |
| Description_TRA |
The Edelbrock #85332 is made specifically for Jeep 4.0L |
| Description_TRA |
Installation is the same as for original equipment cylinder heads. |
| Description_TRA |
Consult service manual for specific procedures, if necessary. |
| Description_TRA |
Be sure that the surface of the block and the surface of the head are thoroughly cleaned to remove any oily film before installation. |
| Description_TRA |
Use alcohol or lacquer thinner on a lint-free rag to clean. Apply oil or suitable thread lubricant to head bolt threads and the underside of bolt heads and washers. |
| Description_TRA |
Torque cylinder head bolts in three steps following the factory tightening sequence |
| RGL |
WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov. |
| Length |
(7) 3.75 in, (7) 4.50 |
| Grade Type |
Performance |
| Quantity |
Kit |
| Finish |
Black Oxide |
| Length |
3.0000 |
| Width |
5.0000 |
| Height |
7.0000 |
| Weight |
5.0000 |
